Email Bounce Rate: What's Good for Cold Email and How to Lower It
TL;DR: Bounce rate is the share of sent emails that came back undelivered. For cold outreach, treat anything under 2% as healthy, 3% as a warning and 5% as the point where you stop sending and clean the list. Most of the problem comes from one source: addresses that no longer exist.
Email bounce rate is the percentage of sent emails that the receiving server rejected, calculated as bounced emails divided by sent emails, times 100. Send 400 cold emails, get 12 back, and your bounce rate is 3%. Mailbox providers read a high rate as a sign that you mail people you don't know, so it drags down where the rest of your email lands.
Hard bounce vs. soft bounce: what's the difference?
Every rejected email comes back with a status code. RFC 3463, the standard that defines these codes, splits failures into two classes:
| Hard bounce | Soft bounce | |
|---|---|---|
| Code class | 5.x.x, a permanent failure | 4.x.x, a temporary failure |
| Typical cause | The mailbox or domain doesn't exist (5.1.1 means "the mailbox specified in the address does not exist") | Full inbox, server down, message too large, rate limiting |
| Will a retry work? | No | Often, after a delay |
| What to do | Remove or fix the address before the next send | Let the system retry; stop mailing the address if it keeps failing |
Hard bounces are the ones that damage your reputation, because they show the address was never checked. Soft ones are mostly noise unless the same address fails send after send.
What is a good bounce rate for cold email?
There's no official cut-off from Gmail or Outlook, so the useful reference points come from the senders who enforce one. Amazon SES (2026) tells customers to stay below 5%, places an account under review at 5% and may pause sending at 10%.
For cold email, where lists are bought or scraped rather than opted in, aim lower:
- Under 2%: healthy. Keep doing what you're doing.
- 2–3%: check the last list you imported.
- 3–5%: warning. Slow down and verify before the next send.
- 5% or more: stop that campaign and clean the list first.
These bands match how Connfig rates mailboxes: at 3% over the last 14 days the daily limit is halved, and at 5% after at least 100 sends the mailbox pauses (see the health check).
Why do cold emails bounce?
Almost every high rate traces back to the list, not the copy:
- Old data. People change jobs and companies shut mailboxes. A list built a year ago has addresses that no longer exist.
- Guessed addresses. Patterns like firstname@company.com look plausible but fail when the company uses a different format.
- Typos. One wrong letter in a manual import is a permanent failure.
- Dead domains. The company closed or moved, and the domain no longer accepts email.
- A new sending domain. Receiving servers trust senders they haven't seen before less and may defer or reject their mail, which is why warming up a new domain matters.
- Missing authentication. Without SPF, DKIM and DMARC, some servers reject the message outright. Our setup guide walks through all three records.
How to reduce your bounce rate in 5 steps
- Verify before you import. Run every new list through an email verifier and drop addresses marked invalid. Treat "unknown" or "catch-all" results as risky and send to them in small batches.
- Start from a fresh source. Contact data goes stale faster than you think, so pull it close to the send date instead of reusing an old export.
- Send a small test batch. Mail the first 50 addresses of a new list, wait a day, and read the result before you release the rest.
- Remove hard bounces after every send. Never retry an address that came back with a 5.x.x code. Fix it if it was a typo, delete it if it wasn't.
- Watch the rate per mailbox, not per account. One bad list can hurt a single mailbox while the account average still looks fine.
In Connfig the last step is built in: an address that hard-bounces is blocked on all your sending domains, and the Invalid addresses tab lists it so you can correct a typo with Fix. Before each send, Connfig also checks the recipient's domain in DNS and skips domains that don't accept email.
How to read a sudden spike
A jump from 1% to 6% overnight almost always points to a single import. Sort the failures by campaign and list, then look at the codes:
- Mostly 5.1.1: the list is stale or guessed. Re-verify it before sending again.
- Many failures from one domain: that company changed its email setup or the domain expired.
- Mostly 4.x.x from one provider: you're being rate limited. Lower daily volume for a few days.
- 5.7.x codes: a policy rejection, often authentication. Recheck your DNS records.
FAQ
Is a 10% bounce rate bad?
Yes. At 10%, Amazon SES says it may pause an account, and most cold email tools will have paused the mailbox well before that. Stop sending and verify the list.
Do soft bounces count toward bounce rate?
It depends on the tool. Some count every rejected message, others only permanent ones. Amazon SES counts only hard bounces in the rate it enforces.
Should I resend to an address that soft-bounced?
Yes, once or twice over a few days. If it keeps failing, treat it as invalid.
To see your bounce rate per campaign and per mailbox, create a free Connfig account.
Connfig'i ücretsiz deneyin
Lead bulma, CRM ve e-posta kampanyalarını tek platformda toplayın. Kart bilgisi gerekmez.
Ücretsiz BaşlaRelated Posts
Google Postmaster Tools: Setup and What to Watch for Cold Email
Google's free dashboard for the email you send to Gmail users. How to set it up, which numbers to watch, and why it often stays empty for B2B cold email lists.
How to End a Cold Email: CTA, Sign-Off and Signature
End a cold email with one easy question, a short sign-off and a plain signature. What Gong's data on 304,174 emails says, with a copy-ready example.
How to Use Claude for Sales: 5 Workflows for Small B2B Teams
Five sales jobs you can hand to Claude, from account research to the follow-up email and a Monday pipeline review. Each comes with a ready prompt and the check you still do by hand.